• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change your door lock is an easy and affordable way to improve the security of your home. The process is not for everyone. It requires a certain amount of patience and skill.

The cylinder is inside the knob body. The cylinder is responsible for recognizing the key when it is put into the lock.

The old lock can be removed

The first step to replace the door lock is to take out the old lock. It is a fairly straightforward process, however you should keep certain things in your mind. Make sure that the new lock fits the door. This will ensure that it fits snugly and doesn't leave a gap in the latch or deadbolt plug.

After removing the latch plate, you will be required to search for two screws or bolts on the inside of the casing which are holding the casing in place with the two halves of the lock. Unscrew these with a screwdriver and then remove the lock from the door. If you have a mortise lock, there could be a set screw at the base of the handle, which binds it to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.

You must also remove the deadbolt latch and latch plug from the hole in your door jamb. Install the new lock. If you are replacing a mortise lock, you should also determine the distance between the lock case and the edge of your door to ensure that the new lock will fit.

You may want to replace your lock for various reasons, such as when you suspect that someone else is holding the key or if you've new roommates. You could save money if you take the lock off yourself instead of hiring an expert. It is much easier than you think and can be completed in a matter of a few minutes.

Remove the trim and handle of your door. With a flat screwdriver, pry off the trim. You should be able twist off the majority of it. In certain cases you might be able to remove the handles completely. The next step is to look for a hole on the inside of the handle, and insert an unstraightened clip into it. This will trigger the release mechanism and allow you to remove the handle from the door. Next, examine the inside of the lock to find a small tab that you can press with a flat screwdriver. After the spindle is removed, you are able to remove the cylinder and the housing.

The choice of a new locking system

When it comes time to pick a new lock you have a variety of options. Consider different types of locks, and select one that fits the style of your door. Think about the backset, which is the distance between the edge and the center of lock hole. Also, consider the cross bore, a tiny hole that is located at the edge of your door's frame. Also, be sure to select a lock that is able to be able to fit the door's thickness and swing.

The majority of door locks have been assessed by BHMA and the American National Standards Institute to give you an idea of how they are able to withstand the rigors of use and how difficult to pick or disable. A lock grade 3 might be ideal for a peaceful apartment complex in a rural area, whereas locks of grade 1 may be more appropriate for an area with a lot of traffic, such as an open-air storefront.

Most smart window door lock repair locks require a digital code to open. If you are concerned about hacking or other security concerns, consult an expert locksmith.

Replace the cylinder

If the cylinder of your door lock is damaged or broken window lock repair you can repair it in a matter of minutes by completing a do-it-yourself project. It is crucial to choose the appropriate cylinder and follow all instructions. The first step is to take off the handle or knob in the event that one is present then loosen the trim around the base of the lock cylinder using the help of a screwdriver. After the trim has been removed, you can take off the screws that hold the cylinder in position with the flathead. The cylinder can then be gently removed from the door.

Before installing the new cylinder, you must make sure that it's the right length for your door. Take a measurement of the distance from the center to the right and left sides of the cylinder using the aid of a tape measure. Purchase a new cylinder that has the same measurements. This will stop the cylinder from snapping, which can you replace locks on upvc windows occur when the door is kicked out or when the key sticks inside.

Insert the replacement window lock cylinder in the door, and then turn the key. This will align the cylinder with the carriage which is located usually on the outside of your lock. You can then loosen the set screws which should be only a couple of turns into the head. If there is a screw located on the exterior of the case that is holding the door, you'll need to remove it.

After taking the lock cylinder out after which you can replace it with a new lock by sliding the new cylinder into the case and tightening the set screw. It is also recommended to reinstall the bracket that connects the cylinder to the stem for the lock indicator and this can be done by pulling up three tabs on the back of the cylinder using needle-nose pliers. Attach the smaller bracket to the back of the cylinder. You must then install the latch plate and strike plate, along with the retaining rings that are fixed to the top of the replacement window lock the cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing an existing lock. The majority of residential locksets are designed for a door thickness of 1 3/8 - 3/4 inch. If your door is more thick you will require a door kit that is thick and includes longer screws, an extended tail piece (for door knobs) or spindle extensions (for deadbolts).

The majority of locks come with a thorough installation guide to aid you. Before you begin, go through the instructions to ensure you've followed all the steps. The manual will also give you an idea of the degree of skill required to complete the task. You may want to ask a person who has had experience in changing locks for help if you are changing locks for the first time.

Before installing the new lock it's a good idea to cover the openings with tape the old hardware. This will stop the screws from slipping out of the holes and will protect any tile you might have installed in the area. It also helps prevent potential damage from rust, grime, dirt and. SECURAM Touch comes with a piece of painter's tape, which is designed to be used for this purpose, but you can also use gaffer's tape as well as masking tape in the event that you have it.

After you have removed the screws holding the inside of the lock section to the outside side, pull it straight away. It's important to do this swiftly so that the lock doesn't end up accidentally closing itself and damage the mechanism.

If your new lock has an internal latch bolt, insert the new latch bolt into the upper cross bore. Be sure to put it in the correct position as indicated by an illustration on the faceplate. Then, screw the latch plate onto the bolt.

Screw the deadbolt to the jamb of the door. Try the deadbolt a few times, throwing it around to see if it extends into the strike plate. Follow the steps that come with your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying you identity and connecting to the wireless network to connect your device.